251805363 Front Drive Shaft Assembly for XCMG LW500FN Wheel Loaders

251805363 identifies a front drive shaft assembly used as an application reference for XCMG wheel loaders. The shaft transmits drive from the transmission side to the front axle. Length, flange pattern, spline and sliding-joint arrangement must match the machine; appearance alone is not a sufficient ordering check.

● Replacement of a worn or damaged drive shaft after the cause of the damage has been investigated

● Vibration or noise under drive after joints, flanges, mounting bolts and the connected components have been checked

● Quotations that must state whether flange hardware and guards are included

251805363 is the reference part number used to identify and review this product. XCMG identifies the equipment application and does not automatically define the brand of every quoted unit. The formal quotation states the supplied brand, condition, assembly scope and included or excluded components.

The application reference for this page is the XCMG LW500FN wheel loader. Final fitment must be checked against the complete machine identification, old-unit identification and relevant interfaces. Do not order by appearance or reference part number alone.

● Complete machine serial number and ID plate

● Old shaft markings or identification, if visible

● Overall length measured on the removed shaft

● Flange diameter, bolt-hole pattern and pilot

● Spline and sliding-joint arrangement

● Joint type, grease fittings and guards

Drive shafts of similar appearance may differ in length, flange diameter and bolt pattern, spline and sliding-joint design and joint size. These dimensions must be measured on the removed shaft. Vibration or noise can also be caused by worn joints, bent tubes, loose mounting, imbalance or damage to the connected components, so the cause of the original failure should be investigated before installing a new shaft.

According to customer requirements and current sourcing conditions, potential solutions may include a verified genuine option when available, a branded replacement or an aftermarket replacement. Availability is confirmed for each enquiry.

● Actual supplied brand and product condition

● Overall length, flange and spline configuration shown in the quotation photos

● Whether bolts, guards and grease fittings are included

● Required quantity

● Warranty terms for the selected option

● Lead time for the quoted supply

For quotation, send the LW500FN machine identification, old-unit identification and the clearest interface photos.

● Measure overall length and compare flange diameter, bolt pattern and spline.

● Confirm whether bolts, guards and grease fittings are included.

● Inspect the connected flanges, bearings and mounting points for wear or damage.

● Check the replacement for straightness and free joint movement before installation.

A drive shaft is long and can bend if supported unevenly. It is supported along its length, the flanges and splines are protected, and the sliding section is secured so it cannot extend in transit.

The shipping method, freight and estimated transit time will be confirmed according to the quantity, packed dimensions, weight and destination.

Warranty terms depend on the selected supply option and will be stated in the formal quotation. Actual pre-shipment photos can be provided.

Based in Xuzhou, China, VTS focuses on construction machinery parts supply and fitment support for international buyers.

● Fitment support focuses on the serial number, overall length, flange diameter and bolt pattern, spline and joint arrangement.

● The quotation distinguishes the supplied brand, condition, included components and assembly scope.

● Confirmed related excavator parts can be consolidated, with international shipping coordinated for the actual order.

How is 251805363 fitment confirmed?

Send the machine serial number, the overall length measured on the old shaft and clear photos of both flanges and the splines.

Can a shaft of similar length be used?

Not without comparing flange diameter, bolt pattern, spline and joint size.

Are bolts and guards included?

Only items listed in the quotation are included; others can be quoted separately.

Does vibration prove the drive shaft is faulty?

No. Joints, mounting, balance and connected components also need checking.

Why is the length of the old shaft needed?

Length and the sliding-joint arrangement decide whether the shaft fits between the connected units, so it must be measured on the removed shaft.

Can the shaft ship with other wheel loader parts?

Yes, where practical, with the shaft supported and protected along its length.

For quotation, send the LW500FN machine identification, old-unit identification and the clearest interface photos.