VOE14612482 Swing Motor for Volvo EC480D Excavators

VOE14612482 identifies the swing motor used as an application reference for Volvo crawler excavators. The unit converts hydraulic power into controlled upperstructure rotation through a reduction section and output pinion. Because the swing drive handles high rotating inertia, correct brake, relief, drain, mounting and gear-interface configuration is essential; VTS confirms these points and the quoted assembly scope from the old unit.

● Replacement or planned overhaul of the swing motor after related system faults have been separated

● Noise or overheating during swing after oil condition and case-drain flow have been checked

● Replacement where the serial number and old motor ID plate must be matched before the supply scope is fixed

VOE14612482 is the reference part number used to identify and review this product. Volvo identifies the equipment application and does not automatically define the brand of every quoted unit. The formal quotation states the supplied brand, condition, assembly scope and included or excluded components.

The application references for this page are the Volvo EC480D and EC480E crawler excavators. Final fitment must still be checked against the complete machine serial number, old-part identification and interface configuration. Do not order by appearance or reference part number alone.

● Complete machine serial number and ID plate

● Hydraulic motor, reduction case and output-pinion scope

● Upper flange, lower mounting and locating diameters

● Main, return, drain, pilot and brake ports

● Relief and make-up valve configuration

● Output-pinion tooth data and swing-bearing relationship

Swing motors may differ in mounting flange, output-pinion connection, valve block, brake and relief arrangement, case-drain routing and whether the reducer is included. Compare the removed unit's identification, output, ports, valves and supply scope. Appearance or the reference part number alone cannot confirm the correct configuration.

Verified genuine option when available, branded or aftermarket replacement, remanufactured or used. Confirmed for each enquiry. The quotation will define the actual supplied brand, condition and assembly scope for this product.

● Actual supplied brand and product condition

● Exact assembly scope and included or excluded components

● Order quantity, applicable warranty terms and lead time

● Packing, Incoterms and payment terms

For quotation, send the EC480D machine identification, old-unit identification and the clearest interface photos.

● Define whether the quotation covers the motor only, the motor with reducer or a wider swing-drive scope.

● Compare the output pinion, mounting flange, valve block, brake, relief, drain and pilot connections with the removed unit.

● Check brake-release pressure, relief or make-up valves, case-drain restriction, reduction gears and swing-bearing contact before replacement.

● Follow the service procedure for drain routing, lubrication, mounting alignment and initial operation.

Open hydraulic ports, the drive shaft, mounting flange, regulator and external controls will be protected against impact and contamination. The heavy pump will be supported and secured, with moisture protection suited to the chosen shipping method.

The shipping method, freight and estimated transit time will be confirmed according to the quantity, packed dimensions, weight and destination.

Warranty terms depend on the selected supply option and will be stated in the formal quotation. Actual pre-shipment photos can be provided.

Based in Xuzhou, China, VTS focuses on construction machinery parts supply and fitment support for international buyers.

● Fitment support focuses on the serial number, motor ID plate, flange, output shaft and case-drain port.

● The quotation distinguishes the supplied brand, condition, included components and assembly scope.

● Confirmed related excavator parts can be consolidated, with international shipping coordinated for the actual order.

How is VOE14612482 fitment confirmed?

The quotation will state the exact motor, reducer, output-pinion and valve scope.

Why is the output pinion photo required?

To verify tooth configuration, installation geometry and the relationship with the swing bearing.

Can a unit with different valve blocks be used?

Not without confirming brake, relief, make-up, drain and pilot functions for the machine.

What can cause harsh swing stopping?

Brake timing, relief settings, contamination, pinion backlash and reduction-gear wear can all contribute.

How is the tall assembly kept safe in transit?

It is base-mounted, braced against tipping and protected at the pinion, ports and upper valve block.

Can actual photos be supplied before shipment?

Yes, photos of the selected configuration can be provided before dispatch as agreed in the order.

For quotation, send the EC480D or EC480E machine identification, old-unit identification and the clearest interface photos.