800901158 Brake Valve Assembly for XCMG LW500FN Wheel Loaders

800901158 identifies a brake valve assembly used as an application reference for XCMG wheel loaders. The valve assembly controls the brake circuit when the operator applies the brake. Port layout, circuit configuration, mounting and any pedal or linkage connection must match the machine; appearance alone is not a sufficient ordering check. Brake components are safety-related, so VTS checks the identification before the quotation is issued.

● Replacement of a brake valve assembly after leakage or damage has been confirmed and related circuit faults separated

● Weak or uneven braking after supply, lines, brake units and linkage have been checked

● Quotations that must state whether the pedal, mounting parts and fittings are included

800901158 is the reference part number used to identify and review this product. XCMG identifies the equipment application and does not automatically define the brand of every quoted unit. The formal quotation states the supplied brand, condition, assembly scope and included or excluded components.

The application reference for this page is the XCMG LW500FN wheel loader. Final fitment must be checked against the complete machine identification, old-unit identification and relevant interfaces. Do not order by appearance or reference part number alone.

● Complete machine serial number and ID plate

● Old valve label and visible markings

● Port count, size and layout

● Circuit configuration and connected lines

● Pedal, linkage or actuator connection

● Mounting points and bracket arrangement

Brake valves of similar appearance may differ in port count and layout, circuit configuration, actuator connection and mounting arrangement. These points must match the removed unit and the machine's brake circuit. Because brake components are safety-related, the valve should be identified from the machine serial number and old-unit markings rather than appearance. Poor braking can also come from supply, lines, brake units, linkage or leakage elsewhere in the circuit, so related conditions should be checked before replacement.

According to customer requirements and current sourcing conditions, potential solutions may include a verified genuine option when available, a branded replacement or an aftermarket replacement. Availability is confirmed for each enquiry.

● Actual supplied brand and product condition

● Valve assembly scope and whether the pedal, mounting parts and fittings are included

● Port and circuit configuration shown in the quotation photos

● Required quantity

● Warranty terms for the selected option

● Lead time for the quoted supply

For quotation, send the LW500FN machine identification, old-unit identification and the clearest interface photos.

● Photograph and label each connected line before removal.

● Match port layout, circuit configuration and actuator connection with the quotation photos.

● Confirm whether the pedal, fittings and mounting parts are included.

● Check lines, brake units and linkage for leakage or damage, and test the brakes as the service procedure requires.

Port openings are sealed against dust and moisture, and the valve and any exposed linkage connection are protected from impact.

The shipping method, freight and estimated transit time will be confirmed according to the quantity, packed dimensions, weight and destination.

Warranty terms depend on the selected supply option and will be stated in the formal quotation. Actual pre-shipment photos can be provided.

Based in Xuzhou, China, VTS focuses on construction machinery parts supply and fitment support for international buyers.

● Fitment support focuses on the serial number, valve label, port layout, circuit configuration and actuator connection.

● The quotation distinguishes the supplied brand, condition, included components and assembly scope.

● Confirmed related excavator parts can be consolidated, with international shipping coordinated for the actual order.

How is 800901158 fitment confirmed?

Send the machine serial number, the old valve label and clear photos of the ports, lines and actuator connection.

Is the pedal included?

Only when the quotation lists it; related parts can be quoted separately.

Can a similar-looking brake valve be used?

Not without comparing port layout, circuit configuration and the actuator connection.

Does weak braking prove the valve is faulty?

No. Supply, lines, brake units, linkage and leakage should be checked as well.

Why should each line be labelled before removal?

Port positions and circuit connections must be restored correctly, and labelled photos also help VTS compare the replacement.

Can the valve ship with other wheel loader parts?

Yes, where practical, with the valve sealed and protected separately.

For quotation, send the LW500FN machine identification, old-unit identification and the clearest interface photos.